Product SiteDocumentation Site

Chapter 7. Booting the Installer

7.1. Starting the Installation Program
7.1.1. Booting the Installation Program on x86, AMD64, and Intel 64 Systems
7.1.2. The Boot Menu
7.1.3. Additional Boot Options
7.2. Booting from the Network using PXE

Important — UEFI for 32-bit x86 systems

Fedora 20 does not support UEFI booting for 32-bit x86 systems. Only BIOS booting is supported.

Important — UEFI for AMD64 and Intel 64

Note that the boot configurations of UEFI and BIOS differ significantly from each other. Therefore, the installed system must boot using the same firmware that was used during installation. You cannot install the operating system on a system that uses BIOS and then boot this installation on a system that uses UEFI.
Fedora 20 supports version 2.2 of the UEFI specification. Hardware that supports version 2.3 of the UEFI specification or later should boot and operate with Fedora 20, but the additional functionality defined by these later specifications will not be available. The UEFI specifications are available from http://www.uefi.org/specs/agreement/
To start the installation program from a Fedora DVD or from minimal boot media, follow this procedure:
  1. Disconnect any external FireWire or USB disks that you do not need for installation. Refer to Section 4.3.3, “ FireWire and USB Disks ” for more information.
  2. Power on your computer system.
  3. Insert the media in your computer.
  4. Power off your computer with the boot media still inside.
  5. Power on your computer system.
You might need to press a specific key or combination of keys to boot from the media. On most computers, a message appears briefly on the screen very soon after you turn on the computer. Typically, it is worded something like Press F10 to select boot device, although the specific wording and the key that you must press varies widely from computer to computer. Consult the documentation for your computer or motherboard, or seek support from the hardware manufacturer or vendor. On Apple computers, the C key boots the system from the DVD drive. On older Apple hardware you might need to press Cmd+Opt+Shift+Del to boot from the DVD drive.
If your computer does not allow you to select a boot device as it starts up, you might need to configure your system's Basic Input/Output System (BIOS) to boot from the media.
To change your BIOS settings on an x86, AMD64, or Intel 64 system, watch the instructions provided on your display when your computer first boots. A line of text appears, telling you which key to press to enter the BIOS settings.
Once you have entered your BIOS setup program, find the section where you can alter your boot sequence. The default is often C, A or A, C (depending on whether you boot from your hard drive [C] or a diskette drive [A]). Change this sequence so that the DVD is first in your boot order and that C or A (whichever is your typical boot default) is second. This instructs the computer to first look at the DVD drive for bootable media; if it does not find bootable media on the DVD drive, it then checks your hard drive or diskette drive.
Save your changes before exiting the BIOS. For more information, refer to the documentation that came with your system.

Note — Aborting the Installation

To abort the installation, either press Ctrl +Alt+Del or power off your computer with the power switch. You may abort the installation process without consequence at any time prior to selecting Begin Installation on the Installation Summary Menu. Fedora makes no permanent changes to your computer until that point. Please be aware that stopping the installation after partitioning has begun can leave your computer unusable.

7.1. Starting the Installation Program

Important — UEFI for 32-bit x86 systems

Fedora 20 does not support UEFI booting for 32-bit x86 systems. Only BIOS booting is supported.

Important — UEFI for AMD64 and Intel 64

Note that the boot configurations of UEFI and BIOS differ significantly from each other. Therefore, the installed system must boot using the same firmware that was used during installation. You cannot install the operating system on a system that uses BIOS and then boot this installation on a system that uses UEFI.
Fedora 20 supports version 2.2 of the UEFI specification. Hardware that supports version 2.3 of the UEFI specification or later should boot and operate with Fedora 20, but the additional functionality defined by these later specifications will not be available. The UEFI specifications are available from http://www.uefi.org/specs/agreement/
To start, first make sure that you have all necessary resources for the installation. If you have already read through Chapter 4, Planning for Installation on the x86 Architecture, and followed the instructions, you should be ready to start the installation process. When you have verified that you are ready to begin, boot the installation program using the Fedora DVD or any boot media that you have created.

7.1.1. Booting the Installation Program on x86, AMD64, and Intel 64 Systems

You can boot the installation program using any one of the following media (depending upon what your system can support):
  • Fedora DVD — Your machine supports a bootable DVD drive and you have the Fedora installation DVD.
  • Fedora live CD — Your machine supports a bootable CD drive and you have a Fedora live CD.
  • Boot CD-ROM — Your machine supports a bootable CD-ROM drive and you want to perform network or hard drive installation.
  • USB flash drive — Your machine supports booting from a USB device.
  • PXE boot via network — Your machine supports booting from the network. This is an advanced installation path. Refer to Chapter 13, Setting Up an Installation Server for additional information on this method.
To create a boot CD-ROM or to prepare your USB flash drive for booting or installation, refer to Section 3.3, “Making Minimal Boot Media”.
Insert the boot media and reboot the system.
You might need to press a specific key or combination of keys to boot from the media. On most computers, a message appears briefly on the screen very soon after you turn on the computer. Typically, it is worded something like Press F10 to select boot device, although the specific wording and the key that you must press varies widely from computer to computer. Consult the documentation for your computer or motherboard, or seek support from the hardware manufacturer or vendor. On Apple computers, the C key boots the system from the DVD drive. On older Apple hardware you might need to press Cmd+Opt+Shift+Del to boot from the DVD drive.
If your computer does not allow you to select a boot device as it starts up, you might need to configure your system's Basic Input/Output System (BIOS) to boot from the media.
To change your BIOS settings on an x86, AMD64, or Intel 64 system, watch the instructions provided on your display when your computer first boots. A line of text appears, telling you which key to press to enter the BIOS settings.
Once you have entered your BIOS setup program, find the section where you can alter your boot sequence. The default is often C, A or A, C (depending on whether you boot from your hard drive [C] or a diskette drive [A]). Change this sequence so that the DVD is first in your boot order and that C or A (whichever is your typical boot default) is second. This instructs the computer to first look at the DVD drive for bootable media; if it does not find bootable media on the DVD drive, it then checks your hard drive or diskette drive.
Save your changes before exiting the BIOS. For more information, refer to the documentation that came with your system.
After a short delay, the graphical boot screen appears, which contains information on a variety of boot options. Installation program automatically begins if you take no action within the first minute. For a description of the options available on this screen, refer to Section 7.1.2, “The Boot Menu”.
Alternatively, press the Esc key to access the boot: prompt, at which you can enter additional boot options as described in Section 7.1.3, “Additional Boot Options”.

7.1.2. The Boot Menu

The boot media displays a graphical boot menu with three options:
Install Fedora
Choose this option to install Fedora onto your computer system using the graphical installation program.
Test this media and install Fedora
This option is the default. Choose this option to first test the integrity of the installation media before installing Fedora onto your computer system using the graphical installation program.
Troubleshooting
This option leads to a menu with several additional boot options.
If no key is hit within 60 seconds, the default boot option runs. To choose the default, either wait for the timer to run out or hit Enter on the keyboard. To choose another option, use the arrow keys on your keyboard and hit Enter when Troubleshooting is highlighted. If you want to customize the boot options for a particular option, press the Tab key. To access the boot: prompt at which you can specify custom boot options, press the Esc key and refer to Section 7.1.3, “Additional Boot Options”.
The Boot Screen
The boot screen
Figure 7.1. The Boot Screen

For a listing and explanation of common boot options, refer to Chapter 11, Boot Options.
The boot options in the Troubleshooting menu are:
Install Fedora in basic graphics mode
This option allows you to install Fedora in graphical mode even if the installation program is unable to load the correct driver for your video card. If your screen appears distorted or goes blank when using the Install Fedora option, restart your computer and try this option instead.
Rescue a Fedora system
Choose this option to repair a problem with your installed Fedora system that prevents you from booting normally. Although Fedora is an exceptionally stable computing platform, it is still possible for occasional problems to occur that prevent booting. The rescue environment contains utility programs that allow you fix a wide variety of these problems.
Run a memory test
This option runs an exhaustive test on the memory on your system. For more information, refer to Section 11.3.1, “Loading the Memory (RAM) Testing Mode”.
Boot from local drive
This option boots the system from the first installed disk. If you booted this disc accidentally, use this option to boot from the hard disk immediately without starting the installer.

7.1.3. Additional Boot Options

While it is easiest to boot using a DVD and perform a graphical installation, sometimes there are installation scenarios where booting in a different manner may be needed. This section discusses additional boot options available for Fedora.
To pass options to the boot loader on an x86, AMD64, or Intel 64 system, press the Esc key at boot time. The boot: prompt appears, at which you can use the boot loader options described below.
Refer to Chapter 8, Configuring Installation Source for boot options to specify your installation source, or to Chapter 11, Boot Options for additional boot options not covered in this section.

Note

Boot options are not available during live image installations.
  • To perform a text mode installation, at the installation boot prompt, type:
    linux text
  • ISO images have an SHA256 checksum embedded in them. To test the checksum integrity of an ISO image, at the installation boot prompt, type:
    linux rd.live.check
    This checksum operation can be performed on any Fedora DVD. It is strongly recommended to perform this operation on any Fedora DVD that was created from downloaded ISO images. This command works with the DVD, hard drive ISO, and NFS ISO installation methods.
  • If you need to perform the installation in serial mode, type the following command:
    linux console=<device>
    For text mode installations, use:
    linux text console=<device>
    In the above command, <device> should be the device you are using (such as ttyS0 or ttyS1). For example, linux text console=ttyS0.
    Text mode installations using a serial terminal work best when the terminal supports UTF-8. Under UNIX and Linux, Kermit supports UTF-8. For Windows, Kermit '95 works well. Non-UTF-8 capable terminals works as long as only English is used during the installation process. An enhanced serial display can be used by passing the utf8 command as a boot-time option to the installation program. For example:
    linux console=ttyS0 utf8

7.1.3.1. Kernel Options

Options can also be passed to the kernel. For example, to apply updates for the anaconda installation program from a USB storage device enter:
linux updates
For text mode installations, use:
linux text updates
This command results in a prompt for the path to the device that contains updates for anaconda. It is not needed if you are performing a network installation and have already placed the updates image contents in rhupdates/ on the server.
After entering any options, press Enter to boot using those options.
If you need to specify boot options to identify your hardware, please write them down. The boot options are needed during the boot loader configuration portion of the installation (refer to Section 9.11.2, “x86, AMD64, and Intel 64 Boot Loader Installation” for more information).
For more information on kernel options refer to Chapter 11, Boot Options.