Product SiteDocumentation Site

Chapter 10. Boot Options

10.1. Configuring the Installation System at the Boot Menu
10.1.1. Specifying the Language
10.1.2. Configuring the Interface
10.1.3. Updating anaconda
10.1.4. Specifying the Installation Method
10.1.5. Manually Configuring the Network Settings
10.2. Enabling Remote Access to the Installation System
10.2.1. Enabling Remote Access with VNC
10.2.2. Connecting the Installation System to a VNC Listener
10.3. Logging to a Remote System During the Installation
10.3.1. Configuring a Log Server
10.4. Automating the Installation with Kickstart
10.5. Enhancing Hardware Support
10.5.1. Overriding Automatic Hardware Detection
10.6. Using the Maintenance Boot Modes
10.6.1. Loading the Memory (RAM) Testing Mode
10.6.2. Verifying boot media
10.6.3. Booting Your Computer with the Rescue Mode
10.6.4. Upgrading your computer
The Fedora installation system includes a range of functions and options for administrators. To use boot options, enter linux option at the boot: prompt.
If you specify more than one option, separate each of the options by a single space. For example:
linux option1 option2 option3

Anaconda Boot Options

The anaconda installer has many boot options, most are listed on the wiki

Kernel Boot Options

The page lists many common kernel boot options. The full list of kernel options is in the file /usr/share/doc/kernel-doc-version/Documentation/kernel-parameters.txt, which is installed with the kernel-doc package.

Rescue Mode

The Fedora installation and rescue discs may either boot with rescue mode, or load the installation system. For more information on rescue discs and rescue mode, refer to Section 10.6.3, “Booting Your Computer with the Rescue Mode”.

10.1. Configuring the Installation System at the Boot Menu

You can use the boot menu to specify a number of settings for the installation system, including:
  • language
  • display resolution
  • interface type
  • Installation method
  • network settings

10.1.1. Specifying the Language

To set the language for both the installation process and the final system, specify the ISO code for that language with the lang option. Use the keymap option to configure the correct keyboard layout.
For example, the ISO codes el_GR and gr identify the Greek language and the Greek keyboard layout:
linux lang=el_GR keymap=gr

10.1.2. Configuring the Interface

To use a specific display resolution, enter resolution=setting as a boot option. For example, to set the display resolution to 1024×768, enter:
linux resolution=1024x768
To run the installation process in text mode, enter:
linux text
To enable support for a serial console, enter serial as an additional option.
Use display=ip:0 to allow remote display forwarding. In this command, ip should be replaced with the IP address of the system on which you want the display to appear.
On the system you want the display to appear on, you must execute the command xhost +remotehostname, where remotehostname is the name of the host from which you are running the original display. Using the command xhost +remotehostname limits access to the remote display terminal and does not allow access from anyone or any system not specifically authorized for remote access.

10.1.3. Updating anaconda

You can install Fedora with a newer version of the anaconda installation program than the one supplied on your installation media.
The boot option
  linux updates
presents you with a prompt that asks you for a disk image containing anaconda updates. You do not need to specify this option if you are performing a network installation and have already placed the updates image contents in rhupdates/ on the server.
To load the anaconda updates from a network location instead, use:
  linux updates=
followed by the URL for the location where the updates are stored.

10.1.4. Specifying the Installation Method

Use the askmethod option to display additional menus that enable you to specify the installation method and network settings. You may also configure the installation method and network settings at the boot: prompt itself.
To specify the installation method from the boot: prompt, use the repo option. Refer to Table 10.1, “Installation methods” for the supported installation methods.
Table 10.1. Installation methods
Installation method Option format
DVD drive repo=cdrom:device
Hard Drive repo=hd:device/path
HTTP Server repo=http://host/path
FTP Server repo=ftp://username:password@host/path
NFS Server repo=nfs:server:/path
ISO images on an NFS Server repo=nfsiso:server:/path

10.1.5. Manually Configuring the Network Settings

By default, the installation system uses DHCP to automatically obtain the correct network settings. To manually configure the network settings yourself, either enter them in the Configure TCP/IP screen, or at the boot: prompt. You may specify the ip address, netmask, gateway, and dns server settings for the installation system at the prompt. If you specify the network configuration at the boot: prompt, these settings are used for the installation process, and the Configure TCP/IP screen does not appear.
This example configures the network settings for an installation system that uses the IP address
linux ip= netmask= gateway= dns=,